I'm gearing up to attempt some cigar box* lutherie for the first time in a long long time.

I remember the article in an early issue of MAKE magazine that arguably kicked off an entire internet cigar box guitar revolution. At the time I thought it the article was cool, but I was too obsessed with Real Lutherie™ at the time to embrace the low-fi/makeshift aesthetic. I did manage to make one cigar box instrument that was way overbuilt but not very successful... it was about 85% built when my life was turned upside down by a move and major house renovation. When I finally finished it a few years later, it was promptly stolen out of my truck literally the next day and I took at as a bit of a cosmic "maybe you're just not meant to make instruments" kick to the balls. For that and other reasons I mostly set that itch aside until recently.

It's *wild* how much information there is about lutherie in general now; hundreds of hours of youtube content, etc.

It's also wild to see how Cigar Box Guitar Making™ has become a sort of invented tradition with accepted best practices and standardized scale lengths, tunings, et cetera. That whole "taking part in a time-honored rugged traditional tinged with faux hobo nostalgia, except 99% of what's been written about cigar box guitars has been written by obsessive hobbyist woodworkers on the internet in the last 10 years" thing.

I'm not sure how much of that can be attributed to the C.B. Gitty company, who has built a bit of a cigar box guitar tool and supply empire, but that's got to be part of it.

Anyway, hooray for the goddamned internet; when I was daydreaming about lutherie 15 years ago StewMac was pretty much the only game in town, and they're good but they were certainly priced like the only game in town. It is amazing how much more accessible things like cheap tuning machines have gotten, and how much less trial and error a person might have to do thanks to the hundreds of other people that have trod pathways ahead of them.

* technically, unfinished craft boxes from Michaels until such time as I can get my hands on some actual cigar boxes, which are scarcer in junk shops than they used to be. But that's fine because it also provides an opportunity to play with finishes.

The challenge with work-from-home lunch hours is not allowing yourself to be totally derailed if you use some of your lunch hour to tinker

Show thread

Ran out of daylight to get a decent photo, but at least I managed to get primer and a couple of coats of paint onto it.

I remembered that I had most of a can of "oil rubbed bronze" type metallic paint from my theremin speaker stand which should look pretty cool, I think one more coat should do it. Going to try using plain old minwax polycrylic as a gloss clear coat. I have the notion it will be less fussy than the nitrocellulose lacquer I've been fighting with on the project.

Definitely going to try using grain filler on the next one.

Show thread

This is a slightly better photo after a third coat, still wet, but ultimately just a difficult color to photograph. If I get into this in a sustained way I’ll probably cobble together a light tent for photography

Show thread

I managed to get five or six coats of spray polyurethane on this thing today; looks like brush marks but I think those are actually sanding marks that have been highlighted by multiple layers.

Dubious I’ll be able to sand this enough to get a smooth look (without sanding all the way through to the color layer) - definitely grain filler next time.

Show thread

It's technically past the 24-hour "dry time" window and the finish has lost the ever-so-slightly-rubbery feel it had last evening, but it's still pretty smelly so I'm not going to bring it in and tinker with electronics just yet. (not that it would do me any good without neck/bridge/strings anyway.)

But, I did remember to get a photo of the highly sophisticated bracing I added

Show thread

Alright, there's any number of things I *should* do outside today ahead of the impending storm, but what I'm probably *going* to do is see how far I can get on a neck for the

Show thread

Slightly better shot of the box color in the sun, sitting on top of the still-not-finished body of the

Show thread

Probably going to splurge on that CB Gitty scarf joint miter box because I don’t have a table saw, and it’s relatively cheap (and the one I tried to make myself is not square, lol.) But with a little filler and sanding this should be close enough.

This test fret was about 100x easier to install than any of the ones I did 15 years ago, and that’s definitely thanks to having the right tools (my wife got me the CB gitty fretting kit for my birthday.

Show thread

If I’m going to the trouble of making a scarf joint I might as well add ears so I can give it a nice shape

Show thread

Need to clean up the nut slot some but I think I’m ready to start carving? I think the fret slots came out well despite me having to cut half of them using a speed square as a guide because I got ahead of myself and glued the headstock and heel block on like a dingus

Show thread

My obsessive nerd inclination is to do some CAD to determine the optimal neck angle per bridge placement and location. I used my ancient, offline copy of adobe Illustrator for basic geometry stuff like this for years and years, but it finally stopped working a couple of OS versions ago and I am not going to let adobe bleed me to death for the rest of my life... but I haven't really learned inkscape or (god forbid) an actual CAD package in the meantime, so that would be a whole yak-shaving expedition that's probably a bit of a moot point anyway because it's not like I have any kind of precision finer than "half a degree-ish" on my saw. 🤷‍♂️

My napkin calculations suggest about 6 degrees, which seems like a lot, but the body *and* neck are smaller than most instruments I'm used to, and math is math.

Worst case I can shim the heel one way or the other.

Show thread
Follow

5° probably would have been a little better for the neck angle, but I think 6 is close enough that I’ll be able to fine tune the action just by tinkering with the bridge height 😎

I had forgotten how pleasing it is to shape a neck, doubly so making little curlicues with the spokeshave.

I spent maybe 5-10 minutes at this this morning and my god it is soothingly meditative

Show thread

Things I need to do this morning:

* Close that other browser tab with search results for "shaving horse plans"

Show thread

Me, all day long, but instead of Krusty's Clown College it's working some more on that neck.

I have work deadline BS I need to make more progress on tonight but I'm gonna take some time right now, dammit

Show thread

:unsure_fry: Not sure if spokeshave difficulties are due to dull blade and inexperience, or spokeshave being a cheap piece of junk. Probably a little of both. (I bought it from Grizzly Industrial and wouldn't have spent more then twenty bucks in 2006 dollars on it)

My sharpening stones are a mess, seeing if I can clean/recondition them is a whole other yak shaving expedition I could go on.

Meanwhile, a cheap rasp worked pretty well to rough out the neck. I got it halfway cleaned up starting with 80 grit sandpaper before the mosquitoes chased me inside... there are still some pretty deep gouges but hopefully sanding will go quickly when I'm not being eaten alive.

Realized a major : Because my box lid is like 5/8" tall and the neck is only about 1 1/2" deep, my plan to attach the neck with two lag bolts is not going to work.

But, hopefully I can salvage it by putting a notch in the approprate place in the box lid. (I don't think I described the issue very well, but it will be apparent when I photograph that step.

Show thread

Ran out of daylight again, but I think it’s just about to the “good enough” stage. Will give it another one more session with 220-grit, and then hit it with some grain filler.

Show thread

I had the stain out for the project, so why the hell not. 🤷‍♂️ It will be a little less contrasty against the dark body.

Not sure I’ve ever stained poplar before… not the prettiest wood, at least with this stain. Predictably there are some dodgy spots around the heel where there’s either glue resisting or end-grain/filler soaking up the stain and going dark. Not sure what that resistant spot on the flat part of the heel is from, though.

Show thread

...just realized it *probably* would have been optimal to stain after installing frets; I'll have to be super careful cleaning up fret ends and will almost certainly have to do some touching up if I scuff the wood.

Show thread

Losing the light and I should let the shellac seal coats I put on the neck dry 100% overnight anyway, but there are a few things I can tinker with on the body.

Tomorrow I’m going to attempt using some dark tinted grain filler on the neck and the cabinet.

Show thread

:unsure_fry: I suppose one is expected to use super concentrated universal tint for grain filler, but I also think this is a case where the topcoat will somewhat restore the darker, wet look

Show thread

I do note that the pores are not completely filled here, I only did two coats and I'm not sure my balance of filler:water:pigment (acrylic paint in this case) was thick (or thin) enough; needs practice and experimentation.

I wasn't really after a glass-smooth finish here anyway, and the surface *is* definitely smoother than it was before.

Show thread

I’ve probably pushed it a bit considering how cool and damp it is today, but this is looking pretty great.

Show thread

Attempted to breadboard a bare-bones circuit tonight, but no joy. Not sure if I screwed something up / shorted something out or if my breadboard is just a POS (which it is, I never have any confidence anything is actually making contact.) will try again with fresh eyes in daylight.

Also, I somehow have no LEDs at all? I *know* I bought an assortment once upon a time but that was two moves ago and who knows where they are now

Show thread

Also got some nice component bits and bobs for the in today’s mail.

The switch is absolute overkill (it was hard to get a sense of scale in the product photo) but it is way more satisfyingly tactile than any rocker switch will ever be. You *know* when you’ve turned this switch on.

The pilot lamp jewel works quite nicely with a warm white led, and who could resist these jolly red knobs

Show thread

My working theory is that with a protective layer of tru-oil on the frets that need markers, I’ll be able to glue in some un-stained dowel, cut it flush with a very very good saw I have for such things, and sand it without screwing up the stain

Show thread

It was a nice, but not very realistic working theory. It’s fine, it was already looking pretty rustic, and now it’s relic’d.

Show thread

Should have drilled the tuner holes before starting the finish, of course. Terrible tear-out despite using a sacrificial block behind. Maybe a poplar thing? The wood seems really fibrous. Time for some more filler (and it will be covered up by the machine heads anyway.)

Show thread

I continually forget that most tuning machines are NOT like planetary banjo tuning pegs in that the knob is typically offset from the actual shaft.

I'm probably doing to have to mount two of them "backwards" for aesthetic reasons. 😒

Show thread

:unsure_fry: not sure what’s lack of experience installing frets vs compromising the sharpness of the fret slots by applying finish after cutting them (the grain filler is water based.)

Things seem to be better after doing another pass with the saw to clear debris out of each slot.

With an unradiused fingerboard it seems to me that, once I get all the frets hammered in and filed, I ought to be able to put the entire thing in the jaws of my workmate table to give it a good even press for good measure.

I am going to order a pair of flush-ground nippers right now because I already tell how tedious it’s going to be to file those ends down.

Show thread

That went about like I expected, but filing through the stain was actually a very good “ok that’s enough” indicator; making a note to self to use charcoal or chalk on future projects. I’ve gained an appreciation for how forgiving this stain (basic oil-based Minwax “Honey”) is for touch-ups.

All-told the filing and beveling didn’t take more than 30 minutes or so. Should be able to start putting tru-oil on later today.

Show thread
Show more

@mayor plus, it's a CBG - technical perfection is not the point!

@scruss oh for sure! This is actually the “cabinet” (pretty sure the 1:4” wood is in inadvisably thin, but OTOH it’s only a 4” speaker so 🤷‍♂️) for a 1W practice amp I’m also building.

@mayor ooh, you've just reminded me that with the new job comes unlimited access to a laser cutter, so enclosures r me!

@mayor plus I got a load of decertified aircraft-grade ply (so still many times better than almost every other grade of ply: just don't build a plane out of it) when the makerspace closed so I won't run out of material.

@mayor oops! I've seen worse.

Probably a bit too high-end for a CBG, but I had these one one of my banjos:
pegheds.com/

They're really good!

I also see that my friend Bill Rickard has got his extremely nice banjo tuners in full production ... just as well, given the amount of kit he had to buy to make them

Show more
Show more

@mayor I had similar issues with my one attempt at a old spokeshave I picked up from a thrift store and sharpened. I now just use a course rasp for most of it, then smoother rasps to sand paper as I get to the end.

Sign in to participate in the conversation
Banjotown

The social network of the future: No ads, no corporate surveillance, ethical design, and decentralization! Own your data with Mastodon!