I'm gearing up to attempt some cigar box* lutherie for the first time in a long long time.

I remember the article in an early issue of MAKE magazine that arguably kicked off an entire internet cigar box guitar revolution. At the time I thought it the article was cool, but I was too obsessed with Real Lutherie™ at the time to embrace the low-fi/makeshift aesthetic. I did manage to make one cigar box instrument that was way overbuilt but not very successful... it was about 85% built when my life was turned upside down by a move and major house renovation. When I finally finished it a few years later, it was promptly stolen out of my truck literally the next day and I took at as a bit of a cosmic "maybe you're just not meant to make instruments" kick to the balls. For that and other reasons I mostly set that itch aside until recently.

It's *wild* how much information there is about lutherie in general now; hundreds of hours of youtube content, etc.

It's also wild to see how Cigar Box Guitar Making™ has become a sort of invented tradition with accepted best practices and standardized scale lengths, tunings, et cetera. That whole "taking part in a time-honored rugged traditional tinged with faux hobo nostalgia, except 99% of what's been written about cigar box guitars has been written by obsessive hobbyist woodworkers on the internet in the last 10 years" thing.

I'm not sure how much of that can be attributed to the C.B. Gitty company, who has built a bit of a cigar box guitar tool and supply empire, but that's got to be part of it.

Anyway, hooray for the goddamned internet; when I was daydreaming about lutherie 15 years ago StewMac was pretty much the only game in town, and they're good but they were certainly priced like the only game in town. It is amazing how much more accessible things like cheap tuning machines have gotten, and how much less trial and error a person might have to do thanks to the hundreds of other people that have trod pathways ahead of them.

* technically, unfinished craft boxes from Michaels until such time as I can get my hands on some actual cigar boxes, which are scarcer in junk shops than they used to be. But that's fine because it also provides an opportunity to play with finishes.

The challenge with work-from-home lunch hours is not allowing yourself to be totally derailed if you use some of your lunch hour to tinker

Show thread

Ran out of daylight to get a decent photo, but at least I managed to get primer and a couple of coats of paint onto it.

I remembered that I had most of a can of "oil rubbed bronze" type metallic paint from my theremin speaker stand which should look pretty cool, I think one more coat should do it. Going to try using plain old minwax polycrylic as a gloss clear coat. I have the notion it will be less fussy than the nitrocellulose lacquer I've been fighting with on the project.

Definitely going to try using grain filler on the next one.

Show thread

This is a slightly better photo after a third coat, still wet, but ultimately just a difficult color to photograph. If I get into this in a sustained way I’ll probably cobble together a light tent for photography

Show thread

I managed to get five or six coats of spray polyurethane on this thing today; looks like brush marks but I think those are actually sanding marks that have been highlighted by multiple layers.

Dubious I’ll be able to sand this enough to get a smooth look (without sanding all the way through to the color layer) - definitely grain filler next time.

Show thread

It's technically past the 24-hour "dry time" window and the finish has lost the ever-so-slightly-rubbery feel it had last evening, but it's still pretty smelly so I'm not going to bring it in and tinker with electronics just yet. (not that it would do me any good without neck/bridge/strings anyway.)

But, I did remember to get a photo of the highly sophisticated bracing I added

Show thread

Alright, there's any number of things I *should* do outside today ahead of the impending storm, but what I'm probably *going* to do is see how far I can get on a neck for the

Show thread

Slightly better shot of the box color in the sun, sitting on top of the still-not-finished body of the

Show thread

Probably going to splurge on that CB Gitty scarf joint miter box because I don’t have a table saw, and it’s relatively cheap (and the one I tried to make myself is not square, lol.) But with a little filler and sanding this should be close enough.

This test fret was about 100x easier to install than any of the ones I did 15 years ago, and that’s definitely thanks to having the right tools (my wife got me the CB gitty fretting kit for my birthday.

Show thread

If I’m going to the trouble of making a scarf joint I might as well add ears so I can give it a nice shape

Show thread

Need to clean up the nut slot some but I think I’m ready to start carving? I think the fret slots came out well despite me having to cut half of them using a speed square as a guide because I got ahead of myself and glued the headstock and heel block on like a dingus

Show thread

My obsessive nerd inclination is to do some CAD to determine the optimal neck angle per bridge placement and location. I used my ancient, offline copy of adobe Illustrator for basic geometry stuff like this for years and years, but it finally stopped working a couple of OS versions ago and I am not going to let adobe bleed me to death for the rest of my life... but I haven't really learned inkscape or (god forbid) an actual CAD package in the meantime, so that would be a whole yak-shaving expedition that's probably a bit of a moot point anyway because it's not like I have any kind of precision finer than "half a degree-ish" on my saw. 🤷‍♂️

My napkin calculations suggest about 6 degrees, which seems like a lot, but the body *and* neck are smaller than most instruments I'm used to, and math is math.

Worst case I can shim the heel one way or the other.

Show thread

5° probably would have been a little better for the neck angle, but I think 6 is close enough that I’ll be able to fine tune the action just by tinkering with the bridge height 😎

Show thread

I had forgotten how pleasing it is to shape a neck, doubly so making little curlicues with the spokeshave.

I spent maybe 5-10 minutes at this this morning and my god it is soothingly meditative

Show thread

Me, all day long, but instead of Krusty's Clown College it's working some more on that neck.

I have work deadline BS I need to make more progress on tonight but I'm gonna take some time right now, dammit

Sign in to participate in the conversation

The social network of the future: No ads, no corporate surveillance, ethical design, and decentralization! Own your data with Mastodon!